Skip to content

Audio Processing

EP-PatchStudio includes thorough audio processing to prepare samples for your EP device. These processing options apply when using the Batch Processor or exporting from the Sample Editor.

In the Batch Processor, settings are only applied when you process or export. Your original files are never changed.

Mode Use Case File Size
Mono Most drums, single-source samples 50% smaller
Stereo Pads, ambiences, stereo-recorded samples 2× file size
  • Mono conversion: Sum (L+R Average) averages the two channels. Left Channel Only or Right Channel Only keeps one side
  • Stereo: Preserves both left and right channels

Recommendation

Use mono for drums and most samples (saves space, every EP device has limited storage).

Automatically adjusts audio levels to maximise loudness without clipping.

  • Enabled/Disabled: Toggle normalisation on/off
  • Target Level: -12 dB to 0 dB (default: -6 dB)
  1. Analyses peak level in audio
  2. Scales entire audio to reach target peak level
  3. Preserves dynamic range (proportional scaling)
  • -12dB: Very conservative, lots of headroom for layering/effects
  • -6dB: Balanced (recommended), safe headroom for device
  • -3dB: Loud, minimal headroom
  • 0dB: Maximum loudness, peaks reach full scale (risk of clipping)

Input: Quiet sample with -18dB peak

Normalise to a -6dB target level

→ Output: +12dB gain applied, peak at -6dB

Recommendation

Use a -6dB target level (standard mastering practice, prevents inter-sample peaks).

Automatically removes silence from the start and end of samples.

  • Enabled/Disabled: Toggle silence trimming
  • Threshold: -96 dB to -6 dB in 6 dB steps (default: -60 dB)
  1. Scans from start: finds first sample above threshold
  2. Scans from end: finds last sample above threshold
  3. Trims everything outside these points
  • -84dB: Very sensitive, keeps quiet room noise and reverb tails
  • -60dB: Balanced (recommended), removes silence but keeps reverb
  • -42dB: Aggressive, removes quiet content and reverb tails
  • -36dB: Very aggressive, may cut wanted audio
  • Recorded samples with pre-roll silence
  • Samples with excessive reverb tails
  • Cleaning up field recordings

Recommendation

Use -60dB for most samples. Disable for samples where you want to preserve room tone or reverb.

Transposes audio by semitones without changing duration (time-stretching algorithm).

  • Range: -24 to +24 semitones (-2 octaves to +2 octaves)
  • Default: 0 (no shift)
  • -12 semitones: Octave down (deeper, darker)
  • -7 semitones: Perfect fifth down
  • -5 semitones: Perfect fourth down
  • +12 semitones: Octave up (brighter, tighter)
  • +7 semitones: Perfect fifth up
  • Uses a WSOLA time-stretch, then resamples to change the pitch
  • Preserves duration whilst changing pitch
  • May introduce slight artefacts (formant shifting, metallic quality)

Input: Snare drum at C3 (MIDI 48)

Pitch shift: -12 semitones

→ Output: Snare at C2 (MIDI 36), same duration, deeper/fuller

Recommendation

Use sparingly. Large shifts (>±12 semitones) can sound unnatural. For subtle tuning, use ±1-3 semitones.

The EP-40 Riddim has a 40-second maximum sample duration. When batch processing encounters longer samples, it offers four handling modes:

Behaviour:

  • Pauses processing and shows modal dialogue
  • User chooses: Split, Pitch Up, Trim, or Skip
  • A “Remember my choice for all long samples” switch

Use case: When you want manual control over each long sample.

Behaviour:

  • Automatically splits sample into 40-second chunks
  • Naming: filename_00-40s.wav, filename_40-80s.wav, etc.
  • Cuts the sample at exact 40-second points
  • Only available when you export a ZIP

Example:

Input: 100-second pad

→ Output:

- filename_00-40s.wav (0:00-0:40)

- filename_40-80s.wav (0:40-1:20)

- filename_80-120s.wav (1:20-1:40)

Use case: Ambient pads, loops, long textures that can be split without losing musicality.

Pros: Preserves entire audio

Cons: Creates multiple files, may split mid-phrase

Behaviour:

  • Pitches sample up by +12 semitones (1 octave)
  • Effect: Doubles playback speed, halves duration
  • Can apply multiple times: +12st → +24st if still too long

Example:

Input: 80-second drone (too long)

→ Pitch up +12 semitones

→ Output: 40-second drone, 1 octave higher

Use case: Drones, pads, loops where higher pitch is musically acceptable.

Pros: Single file, preserves continuity

Cons: Changes pitch/character

Behaviour:

  • Keeps the first 40 seconds and cuts off everything after that
  • Your original file isn’t changed

Example:

Input: 100-second sample

→ Output: First 40 seconds only (0:00-0:40)

Use case: When only the intro/start of the sample is needed.

Pros: Simple, single file

Cons: The output loses everything after 40 seconds

Behaviour:

  • Skips file entirely (marked as error in queue)
  • Result: File not processed or included in output

Use case: When long samples shouldn’t be processed (e.g., full songs, stems).

Scenario Recommended Mode Notes
Ambient pads/textures Auto-Split Preserves all audio, can layer chunks
Drones/loops Pitch Up Musical if octave up sounds good
Field recordings Trim to 40s Usually only need beginning
Full tracks/stems Skip Not suitable for device
Mixed batch Ask Manual control per file

The batch processor applies settings in this specific order:

  1. Load audio file (decode to AudioBuffer)
  2. Resample (if target sample rate differs from source)
  3. Convert channels (stereo → mono if selected)
  4. Remove DC offset (if enabled)
  5. Trim silence (if enabled)
  6. Normalise (if enabled)
  7. Pitch shift (if not 0 semitones)
  8. Reverse (if enabled)
  9. Fade in and fade out (if set)
  10. Quantise bit depth (8/10/12/16/24-bit) and export as WAV (16-bit or 24-bit container)

Important

This order is optimised for quality. For example, normalisation happens after trimming silence (so levels are based on actual audio, not silence).

Learn about sample rates, bit depths and audio format options

View Export Options →

Process multiple audio files with automated workflows

View Batch Processor Docs →

Occasional emails about new apps, features and releases.